成都圓管輸送機缺點（一）

核心提示：圓管帶式輸送機也存在缺點，主要是：

成都圓管輸送機缺點（一）

圓管帶式輸送機也存在缺點，主要是：

(1)輸送帶性能要求高

盡管圓管帶式輸送機所采用的輸送帶仍然為平型輸送帶，但是既要將輸送帶導向成圓管形狀，同時要求密封，因此要求輸送帶的邊緣與通用帶式輸送機輸送帶的邊緣不同；另外為了使輸送帶導向成圓管形狀，并且在輸送機運行過程中保持圓管形狀，因而對輸送帶的剛度要求也不同，需要在設計和制造中特別考慮。

(2)運行阻力大

由于運行中物料被包圍在圓管內，增大了物料與輸送帶的擠壓力(亦即托輥與輸送帶間的壓力大)，從而圓管輸送機的運行阻力系數比通用帶式輸送機的大。

(3)輸送量小

圓管帶式輸送機與普通帶式輸送機相比，在帶速和帶寬相同的條件下輸送量小。例如，帶寬為100時，普通帶式輸送機的物料最大截面積為0.094m2(托槽角35，堆積角為10°)，而圓管帶式輸送機的物料截面積為0.0409m2，只相當普通帶式輸送機的物料最大截面積的1/2。

(4)設計計算復雜

由于圓管帶式輸送機的結構比通用帶式輸送機的復雜，因而使其設計計算更加復雜，普通設計人員難以掌握。特別需要指出的是，圓管帶式輸送機的運行阻力隨運動速度的增大而增大，實際設計中運行阻力系數的選擇較困難。